Siemens logo manual 2019

  • Este tópico está vazio.
Visualizando 0 resposta da discussão
  • Autor
    Posts
    • #76742 Responder
      Petteri

      Siemens logo manual 2019
      .
      .
      Download / Read Online Siemens logo manual 2019
      .
      .
      .

      .
      Top element. Related Manuals for Siemens Logo! Summary of Contents for Siemens Logo! Preface, Contents Getting started with LOGO! Software Applications Technical data Manual Determining the cycle time LOGO! Product Info included with all devices. PC, refer to the Online Help for LOGO! Soft Comfort is the programming software for PCs. Contents Writing and starting the circuit program . Which communication modules are available? AS interface, that is described in more detail in a separate documentation. STOP indicator Mechanical coding pins Inputs Slide Mechanical coding sockets Expansion interface Outputs LOGO! STOP indicator sockets Slide Expansion interface LOGO! Symbol Designation Supply Inputs Outputs Properties voltage LOGO! Expansion modules The following expansion modules can be connected to the LOGO! Symbol Name Power supply Inputs Outputs LOGO! Communication modules The following communication modules can be connected to the LOGO! Warning Risk of personal injury and material damage. In potentially explosive atmospheres, always switch off the power supply to LOGO! General guidelines Please note the following guidelines for installing and wiring your LOGO! Always ensure that the wiring of your LOGO! Also, conform with all national and regional regulations when you install and operate the devices. Do not connect an external power supply in parallel to the output load of a DC output. This could develop a reverse current at the output if you have not installed a diode or similar barrier device. Safety of electronic control equipment Introduction The notes below apply regardless of the type or manufacturer of the electronic control. Reliability Maximum reliability of LOGO! Maximum setup Maximum setup of a LOGO! Basic, 4 digital modules and 3 analog modules I1. Setup with different voltage classes Rules Digital modules can only be connected to devices of the same voltage class. Connecting an expansion module to LOGO! R, 230R, DM16 DM16 DM16 PT100, 230R LOGO! Compatiblity All currently available expansion modules are completely compatible with the basic modules of equipment series 0BA3 and 0BA4. DIN rails to EN 50022 or on the wall. Basic has a width of 72 mm, which corresponds with 4 subunits. DIN rail mounting Mounting How to mount a LOGO! Basic module onto the rail and 2. The mounting interlock at the rear must engage LOGO! Using a screwdriver, push the interlock to the left. In its end position the slide interlock engages in the LOGO! Repeat steps 3 through 6 to mount further expansion modules. Note The expansion interface on the last expansion module must be covered. Insert a screwdriver into the eyelet at the bottom of the slide interlock and move the latch downward 2. Using a screwdriver, push the integrate slide interlock to the right 2. Slide the expansion module off towards the right 3. All dimensions in mm Bore hole for O M4 screw Tightening torque 0. You do not need wire ferrules for the terminals. Note Always cover the terminals after you have completed the. Note A power failure may cause an additional edge triggering signal at the special functions, for example. Data of the last uninterrupted cycle are stored in LOGO! Sensor characteristics for LOGO! If, however, you use a switch whose glow lamp is fitted with a power supply, this response does not occur. As an alternative, you can also use an X capacitor rated at 100 nF and 2. I5 and I6 are the same as in the previous versions 0BA0 to 0BA4, i. BA5 units by means of the programming software LOGO! SoftComfort, without any changes to these features. V are supplied when you turn the potentiometer one full rotation. The inputs of these devices are arranged in 2 groups, each consisting of 4 inputs. Different phases are only possible between blocks, but not within the blocks. I1 on the analog expansion module. Use only shielded encoder wires. The potential of the relay contacts is isolated from the power supply and the inputs. Requirements for relay outputs You can connect various loads to the outputs, e. R is missing from their type name. An auxiliary load voltage supply is not necessary, because LOGO! If the bus connection is OK, the LED lights up green. In programming mode, the LED lights up orange. To be able to send data across the AS interface bus to the LOGO! It indicates the number of the input or output in LOGO! Note For detailed information about the networking of LOGO! AS interface bus please refer to the LOGO! Whether a circuit program is stored in LOGO! The application program is loaded into the devices via the EIB interface. The application program is available on the LOGO! KNX, behaviour on communication failure LOGO! If there is a power failure of the LOGO! At this point, we once again refer to LOGO! Soft Comfort, which is the LOGO! A small example in the first part of this chapter introduces the operating principle of LOGO! We shall first show you the meaning of two basic terms, namely the connector and the block. As the next step filexlib.
      .
      Siemens logo 2019 handboek
      Siemens logo 2019 user guide
      Siemens logo 2019 notice
      Siemens logo 2019 lamhleabhar
      Siemens logo 2019 notice

Visualizando 0 resposta da discussão
Responder a: Siemens logo manual 2019
Sua informação: